Imc-networks E1 Manual do Utilizador

IE-iMcV-T1/E1/J1-LineTerm SFP and 1x9 Operation Manual Above illustration is representative; different models available

7 DIP Switch Settings (S2, S3) Switch Settings for Switch S2 T1/E1 Selection S2-1: OFF T1 Mode Selected default S2-1: ON E1 Mode Selected

8 Switch Settings for Switch S3 Reserved S3-1: ON Reserved S3-1: OFF Reserved default Remote Management S3-2: ON Remote Management

9 Features The IE-iMcV-T1/E1/J1-LineTerm, TP/SFP module includes several features to facilitate maintenance and troubleshooting in any T1/E1/J1 based

10 Loopback Modes This feature allows three distinct Loopbacks to be activated either through DIP Switches or iView2 Management. Fiber Loopback An

11 Fault Loopback This switch enables or disables the Fault Loopback feature on the copper port. A normal copper line LOS fault will cause a Remote

12 T1, E1 and J1 Selection This switch selects the data rate to use on the copper line. The data rate selections available include the following: •

13 LED Operation The IE-iMcV-T1/E1/J1-LineTerm, TP/SFP module features several diagnostic LEDs per port. The following LED display functions are pro

14 Loopback Testing The IE-iMcV-T1/E1/J1-LineTerm, TP/SFP includes three Loopback test modes: Copper Loopback, Fiber Loopback and Internal Fiber Loop

15 Pseudorandom Bit Sequence (PRBS) Testing To test using PRBS, configure the IE-iMcV-T1/E1/J1-LineTerm, TP/SFP modules for No Loopback, and then con

16 Use the following LED indications to identify the fault location: *DIP Switch S3-7 must be set to ON for Fault Loopback to operate as illustrated

ii FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A computing device, pursu

17 Specifications Standards Compliance (T1, E1, J1): ANSI T1.102-1993 ANSI T1.107.1995 GR-820-CORE T1, E1, J1 Interface: T1 (1.544 Mbps +/- 32 ppm) E

18 Fiber Optic Cleaning Guidelines Fiber Optic transmitters and receivers are extremely susceptible to contamination by particles of dirt or dust, wh

19 Electrostatic Discharge Precautions Electrostatic discharge (ESD) can cause damage to any product, add-in modules or stand alone units, containing

20 Certifications CE: The products described herein comply with the Council Directive on Electromagnetic Compatibility (2004/108/EC)

19772 Pauling • Foothill Ranch, CA 92610-2611 USA TEL: (949) 465-3000 • FAX: (949) 465-3020 www.imcnetworks.com © 2011 IMC Networks.

iii Table of Contents FCC Radio Frequency Interference Statement ...ii Warranty...

1 About the IE-iMcV-T1/E1/J1-LineTerm, TP/SFP IE-iMcV-T1/E1/J1-LineTerm, TP/SFP is an SNMP-Manageable module that converts standard TDM-based copper

2 NOTE IE-iMcV-T1/E1/J1-LineTerm, TP/SFP with SFP Module can be installed in an iMediaChassis and MediaChassis series. Installing an iMcV-Module iMcV

3 • Required CSU line Buildout (0db to -22db) • Receiver BOOST for T1 and E1 applications • Fiber transceivers must be for appropriate fiber run, i.

4 Configuration Control Some iMcV-Modules offer configuration control; labels on the front faceplate are identified as such. Configuration control ha

5 NOTE If the end user has a mixture of standard iMcV-Modules as well as Configuration Control iMcV-Modules, it is important to understand how SNMP a

6 DIP Switches The IE-iMcV-T1/E1/J1-LineTerm, TP/SFP DIP Switches are located on S2 and S3 on the PCB. The location of the S2 and S3 DIP Switches ar